spiral chute with high quality | fote machinery

spiral chute with high quality | fote machinery

Spiral chute is a kind of high-efficiency gravity separation equipment. It can be used in the materials such as iron ore, ilmenite, chromite, pyrite, zircon, rutile, monazite, tungsten, tin, tantalum, niobium, etc.

Spiral chute, integrated the characteristics of spiral concentrator, shaking table and centrifugal concentrator, is the best equipment for mining and beneficiation, especially for placer mining on seashores, riversides, sand beaches, and streams.

This equipment is suitable for the separation of iron ore, ilmenite, chromite, pyrite, zircon, rutile, monazite, phosphonite, tungsten ore, tin ore, strontium as well as antimony ore and other non-ferrous metals, rare metals and non-metallic mineral bodies with different specific gravity with a particle size of 0.3 - 0.02 mm.

The main part of the spiral chute device is the spiral flight which is made of glass fiber reinforced plastic. The inner surface of the spiral groove is coated with a wear-resistant lining, usually a polyurethane wear-resistant glue or an epoxy resin mixed with artificial gold steel sand.

There are a miner and a feed tank in the upper part of the spiral chute, and a product interceptor and a collecting tank in the lower part. The entire equipment is framed vertically with steel frames.

The spiral chute is similar to the thread shape. The movement of the materials inside can be divided into three stages, which are the material introduction stage, material acceleration phase and material uniform velocity warehouse phase. And the third stage lasts the longest, which is the key for materials crushing.

The key to the design of the spiral chute is in the uniform velocity stage. The main parameters are radius R, bottom plate width b, elevation height h, helix angle mouth, and bottom plate radial inclination angle.

Spiral chutes are widely used in the selection of hematite, the recovery of heavy minerals in tailings, and the selection of rare and non-ferrous metals. This is because it has the following advantages:

It has characteristics of reasonable structure, simple installation, small floor space, simple operation, stable ore dressing, clear mineralization, large processing capacity, high efficiency, high enrichment ratio, high recovery rate and reliable operation.

The spiral chute is not critical to the operation requirements (such as grain size, mass fraction, etc.). Even if the ore supply, ore concentration, ore size and ore grade change, there is almost no influence on the selection index, which means that it has strong adaptability.

The spiral chute is not only easy to operate, but also achieves a good treatment effect. It is characterized by stable ore dressing, clear ore separation, large processing capacity, high efficiency, and high enrichment ratio.

According to the difference in the specific gravity, particle size and shape of the ore, the ore and sand are separated by the gravity and centrifugal force of the swirling flow. The concentrate flows into the concentrate bucket. The tailings flow into the tailing bucket which is connected to the sand pool with the pipe and then they are discharged with the sand pump, completing the whole process of dressing.

The spiral chutes produced by Fote are mainly used in metal mines, coal industry, power environmental protection and other industries. They are sold well at home and abroad, and various types of equipment meet the needs of different industries.

Fote timely follows up product installation and maintenance. In the fierce market competition, relying on leading technical advantages, excellent product quality and perfect after-sales service, Fote's products are exported to more than 200 countries and area.

The gold content in the gold deposit is extremely low, and it is usually necessary to use refining by gravity separation, flotation, amalgamation, magnetic separation and electro-selection, and at the same time, high-efficiency and energy-saving gold ore beneficiation equipment are arranged for beneficiation and enrichment.

Crushing equipment: Jaw crusher. It is flexibly used for gold ore crushing according to different gold selection requirements, further improves gold mining efficiency and recovery rate, and reduces gold mine loss rate.

Washing: Some gold mines have a high mud content, and the soil is very sticky. It is easy to wrap the gold grains in the soil and cannot be extracted. Therefore, for such gold mines with more sticky soil, the first thing to do is the washing of the mine.

Screening: Cylinder washing machine. Because the gold in the gold deposit is free, the monomer dissociation degree of gold and sandstone is very high, and the large river pebbles are gold-free, thus it is necessary to screen the waste rock.

Rough selection equipment: Spiral chute. Gold mine after washing and sieving enters into rough re-election process. Gold mine with lower gold content generally adopts gold chute to raise gold which has a large processing capacity and low ore dressing cost.

Magnetic separation: Magnetic separator. Iron and ferrotitanium contained in gold deposits contain strong magnetism and weak magnetic properties. Different grades of iron concentrate and ferrotitanium powder can be obtained through different magnetic separators.

So far, the set of equipment has been running stably, which has brought considerable benefits to users. Because of its high quality and low price, reliable after-sales service and simple installation, it has attracted more customers.

As a leading mining machinery manufacturer and exporter in China, we are always here to provide you with high quality products and better services. Welcome to contact us through one of the following ways or visit our company and factories.

Based on the high quality and complete after-sales service, our products have been exported to more than 120 countries and regions. Fote Machinery has been the choice of more than 200,000 customers.

spiralchuteseparator

spiralchuteseparator

Model: glass-steel spiralchuteFeed size0.3-0.02mmProduction Capacity: 0.15~8t/hApplication rangeApplicable to sort iron ore, ilmenite, chromite, zirconite, rutile, tungsten ore, tin ore, tantalum-niobium ore of the size between 0.3 and 0.02mm

Model: glass-steel spiralchuteFeed size0.3-0.02mmProduction Capacity: 0.15~8t/hApplication rangeApplicable to sort iron ore, ilmenite, chromite, zirconite, rutile, tungsten ore, tin ore, tantalum-niobium ore of the size between 0.3 and 0.02mm

IntroductionSpiral chute, glass-steel spiral chute and glass-steel rotating spiral chute have these advantages: rationalstructure, convenient installation, easy operation, large handling quantity, high recovery ratio, wear-resisting,reliable performance, noiseless. It is the best mineral processing equipment.

Application of glass-steel spiral chute Glass-steel spiral chute is applicable to sort iron ore, ilmenite, chromite, zirconite, rutile, tungsten ore,tin ore, tantalum-niobium ore of the size between 0.3 and 0.02mm.Principle and application Put up the spiral chute, adjust the vertical line, fix it with iron or wood, ore sand is delivered by sand pumpto two feed inlets of the top of spiral chute, add water to adjust the concentration of ore pulp. The ore pulp flowsfrom the top of spiral chute, there will be centrifugal force during the process of whirl, the effect of gravity andcentrifugal force will separate the ore and sand according to different proportion, granularity and shape of ore sand.Concentrate will enter the concentrate bucket, tailing will enter tailing bucket and discharged by sand pump to finishthe whole process of mineral processing.

Unique advantages of spiral chute There are grooving on the chute surface which improves the mineral enrichment ratio effectively and increases therecovery rate. The grooving on the chute surface makes large and heavy particles move along inner side, small and lightparticles floating on heavy particles flow along outside faster because of centrifugal force, so the separation effectis more obvious, the recovery rate of heavy minerals is 10% higher than ordinary spiral chute, separation effect is closeto the international advanced level.

spiral chute | spiral separator - jxsc machine

spiral chute | spiral separator - jxsc machine

Spiral Chute is the best equipment for mining and mineral processing, which combines the characteristics of the spiral concentrator, shaking table and Centrifugal concentrator. It is made of the fiberglass lined with wear-resistant polyurethane and corundum cover, light moisture-proof, anti-rust. The spiral separator has the advantages of small occupation area, small water consumption, simple structure, no energy consumption, large capacity, easy installation, easy operation, small investment.

We supply different types of gravity separation equipment, such as gold centrifugal concentrator, shaking table, wet spiral concentrator. Spiral classifier applied in different conditions of extraction process dense media separation. Besides, the spiral chute design is available. email us to know the spiral classifier price. Mining equipment list

The Spiral separator/ spiral chute is the earliest mining machine. It has been used to classify the granularity 0.3-0.02 millimeters fine grain like iron, tin, tungsten, tantalum-niobium, gold ore, coal mine, monazite, rutile, zircon, and other metals. The non-metallic minerals which have a big enough specific gravity difference. Spiral chute principleRaise the spiral chute and fix it in the proper position, sand pump send the ore to the feed inlet, adding water to adjust the concentration of the slurry. The slurry naturally swirls from high to low and generates an inertial centrifugal force in the rotating bevel flow rate. The mineral is separated from the sand by the gravity and centrifugal force of the swirl by the difference in specific gravity, grain size and shape of the ore. The concentrate flows into the concentrate bucket and is connected by the pipeline. The tail sand flows into the tailing sand bucket and is connected to the sand pool by the pipeline, and then drained by the sand pump to complete the whole process of the beneficiation.

gravity spiral concentrators,spiral chutes,spiral separators-well-tech international mining equipment

gravity spiral concentrators,spiral chutes,spiral separators-well-tech international mining equipment

Spiral concentrator is our companys concentrating experienced scientific product, which is the best concentrating equipment, especially for concentrating sand ore in beach, riverside, seashore and stream.

Descriptions Spiral concentrator is our companys concentrating experienced scientific product, which is the best concentrating equipment, especially for concentrating sand ore in beach, riverside, seashore and stream. The product is made of the fiberglass lined with wear-resistant resin and emery. It is the domestic advanced level, the new highly effective equipment, it has been widely used in to enrichment the particle size 0.3-0.02 millimeters fine grain like iron, tin, chromite, ilmenite, tungsten, zinc, tantalum-niobium, gold, coal, monazite, rutile, zircon , other low-grade ores or non-metallic minerals which have a enough specific gravity difference.

Our company uses the newest design and a complete set of technology organization produced and strict quality testing to guarantee each specification of spiral separator qualified. We make the serialized with a special kind of grooved spiral separator to be selected by colored, ferrous metal mine, coal chemical industry, coal dressing, sulfur factory as well as the scientific research, the design department, the colleges and universities test chamber.

1 Reasonable structure and small occupation area; 2 High recovery, high efficiency, and precise separation; 3 Non-required power; 4 Light in weight, anti corrosion, rust and wear resistant; 5 Simple installation and minimal maintenance requirements; 6 Low operating cost and long working life; 7 Reliable running with minimal operator attention; 8 Strong adaptability to fluctuation of feeding amount, density, size and grade; 9 The surface of emery forms strong friction the concentration effect surpass plastic surface.

Model 5LL-2000 5LL-1500 5LL-1200 5LL-900 5LL-600 5LL-400 Spiral Diametermm 2000 1500 1200 900 600 400 Spiral Pitchmm 1200 800/680/540 720/540/360 660/540/400 450/360/270 240/180 Starts 3 4 4 4 2 2 Feeding Sizes (mm) 4-0.04 0.8-0.037 0.3-0.03 0.3-0.03 0.2-0.02 0.2-0.02 Feeding Density (%) 20-45 30-60 25-35 25-55 25-55 25-55 Capacity (t/h) 15-40 6-8 4-6 2-3 0.4-0.8 0.15-0.2 Dimension (mm) Length 2300 1560 1360 1060 700 460 Width 2300 1560 1360 1060 700 460 Height 6500 5230 5230 4000 2600 1500 WeightKg 1100 800 600 400 150 50

spiral separator | spiral chute | spiral classifier | mining equipment

spiral separator | spiral chute | spiral classifier | mining equipment

The spiral separator is the best gravity concentrating equipment, especially for concentrating sand ore in seashore and riverside. It is made of the fiberglass, lined with wear-resistant polyurethane and covered with corundum cover. It has advantages such as lightweight, moisture proof, anti-rust and corrosion, noiseless, very suitable for the different feeding particle sizes and grades.

Capacity: 0.15-8t/h Feeding size: 0.3-0.02mm Advantages: 1. Simple structure, easy to operate and maintain 2. Low energy consumption 3. Relate wide range of particle size 4. Small volume, space saving 5. High productivity and efficiency

Main parts: ore distributor, feed chute, spiral chute section, cutting trough, collecting hopper, support, etc. Spiral separator types: single spiral separator, lab spiral separator, rotary spiral separator, multi-deck spiral separator.

Application: The spiral separators are designed for classifying the granularity 0.3-0.02 millimeters fine grain like iron, hematite, ilmenite, chromite, brasses, tin, tungsten, tantalum-niobium, gold ore, coal mine, monazite, rutile, zircon, and other Non-ferrous metal, rare metal, and non-metallic minerals with different specific gravity in the mineral processing plant.

Working principle of spiral separators The ore materials are separated by the specific difference of gravity force, inertial centrifugal force, flow force, and surface friction of the light and heavy ore particles in the downward flow along the spiral tube slope. Generally speaking, the movement of the slurry flow on the spiral concentrating tables surface produces two directions, one is the longitudinal flow which rotates swiftly around the vertical axis of the spiral chute and down along the chute surface, which is called the main flow, the other is the transverse flow which rotates around a balance layer of the ore flow itself, called transverse circulation flow or vice flow. Under the comprehensive action of longitudinal main flow and transverse circulation, the mineral particles on the surface of spiral classifier move differently along longitudinal and transverse direction due to different density, particle size and shape, and settle at the bottom of the spiral groove in different time and speed, so the mineral particles are stratified according to density and particle size.

Stratification is the first stage of the separation process, which is basically completed after the first processing circuit of the spiral separators. After delamination, the light mineral particles in the upper layer flow to the outer edge of the spiral separator machine gradually, while the heavy mineral particles in the lower layer are affected less by the longitudinal main flow and move to the inner edge gradually. In this way, the layered particles are divided again, which is the second stage called zoning, completed after series ( 3-5 times ) sorting process. After the above two stages, the ore intercepting trough and the ore receiving hopper discharge the different grade separation products from the clay trough, and the separation process is completed.

The grain size distribution rule along the cross-section of the wet spiral separator is as follows: under normal ore-feeding conditions, more than 70% of the ore particles are concentrated in the middle of the spiral concentrator beneficiation area; About 20% of the ore grains are located at the inner edge of the chute; Less than 10% of fine ore grains are near the outer margin.

JXSC spiral separator manufacturer ( and other mining equipment) focuses on producing spiral gravity separator decades of year, qualified separator machines popular in the world market of various mineral processing. Contact us to the spiral separator price, installation instruction and special design service. Spiral separator for sale. Click to find more gravity concentration methods in mineral processing.

Mining Equipment Manufacturers, Our Main Products: Gold Trommel, Gold Wash Plant, Dense Media Separation System, CIP, CIL, Ball Mill, Trommel Scrubber, Shaker Table, Jig Concentrator, Spiral Separator, Slurry Pump, Trommel Screen.

Get in Touch with Mechanic
Related Products
Recent Posts
  1. spiral chute separator adalah

  2. guinea high end medium coal magnetic separator

  3. south africa high intensity magnetic separator

  4. magnetic separator belt

  5. magnetic separation technique procedures

  6. gold separating machine mining equipment price kws

  7. machines that separate gold

  8. high end sandstone magnetic separator sell in albania

  9. high telsa dry drum tymagnetic separator

  10. characterization and beneficiation of anka chromite ore using magnetic separation process

  11. charcoal machine price

  12. chinese crush rabbit avi

  13. rod mill diagram

  14. werkmaster grinder prices model

  15. advanced technological ultrafine ball mill

  16. low less consumption gold machine

  17. grinding mill equipments manufacturers in chennai

  18. concrete jaw crusher machine manufacturer

  19. kerala law of crusher working

  20. how to start a cone crusher