Processing ability: 0.216 m/min Impeller rotation speed: 191400 r/min Dimensions: 700700750220029001400 mm Applied material: non-ferrous metals, ferrous metals, precious metals, non-metallic mineral.gold ore, copper ore, silver ore , manganese ore, lead-zinc ore, nickel ore, phosphate ore, etc
Processing ability: 0.216 m/min Impeller rotation speed: 191400 r/min Dimensions: 700700750220029001400 mm Applied material: non-ferrous metals, ferrous metals, precious metals, non-metallic mineral.gold ore, copper ore, silver ore , manganese ore, lead-zinc ore, nickel ore, phosphate ore, etc
Flotation machine is used for classifying in non-ferrous and ferrous metal mineral. SF flotation cell is the mechanical agitation type, and it can draw the inspiration and the pulp. Compared with other flotation plants, its spirit is big; and the power loss is low, and the impeller lap wears lightly.
Flotation cells orflotation separatoris used in classifying in non-ferrous and ferrous metal mineral. SF flotation cellis the mechanical agitation type, and it can draw the inspiration and the pulp. Compared with traditional flotation cell, the power loss is low and the impeller lap wears lightly.
When flotation machineor flotation separator works, slurry is inhaled from the bottom of the trough to the space between impellers. Meanwhile, the low-pressure air sent by fan is sent to this area through the air distributor in the hollow shaft. After sufficient mixing, the slurry is pushed out by the impeller, and then goes to the whole trough. When the froth rises to the stable level, after the enrichment processing, froth overflows to the froth trough from the overflow weir.
(1)The capacity of air suction is large; the power consumption is low. (2)Every flotation machine has three functions of air suction, slurry suction and flotation simultaneously being unique in flotation return circuit without need for any supplement and equipment; the circuit change is convenient for horizontal location. (3)The slurry cycle is rational; the settlement of coarse sand can be reduced into full play. (4)The regulation is convenient to equip auto and electro-controlling arrangements for slutty level.
Industrial flotation machines can be divided into four classes: (1) mechanical, (2) pneumatic, (3) froth separation, and (4) column. The mechanical machine is clearly the most common type of flotation machine in industrial use today, followed by the rapid growth of the column machine. Mechanical machines consist of a mechanically driven impeller, which disperses air into the agitated pulp. In normal practice, this machine appears as a vessel having a number of impellers in series. Mechanical machines can have open flow of pulp between each impeller or are of cell-to-cell designs which have weirs between each impeller. The procedure by which air is introduced into a mechanical machine falls into two broad categories: self-aerating, where the machine uses the depression created by the impeller to induce air, and supercharged, where air is generated from an external blower. The incoming slurry feed to the mechanical flotation machine is introduced usually in the lower portion of the machine.Figure 7 shows a typical industrial flotation cell of each air delivery type.
The most rapidly growing class of flotation machine is the column machine, which is, as its name implies, a vessel having a large height-to-diameter ratio (from 5 to 20) in contrast to mechanical cells. The mechanism behind this machine to is provide a countercurrent flow of air bubbles and slurry with a long contact time and plenty of wash water. As might be expected, the major advantage of such a machine is the high separation grade that can be achieved, so that column cells are often used as a final concentrate cleaning step. Special care has to be exercised in the generation of fine air bubbles and controlling the feed rate to column cells.
Good mixing of pulp. To be effective, a flotation machine should maintain all particles uniformly in suspension within the pulp, including those of relatively high density and/or size. Good mixing of pulp is required for maximizing bubble-particle collision frequency.
Appropriate aeration and dispersion of fine air bubbles. An important requirement of any flotation machine is the ability to provide uniform aeration throughout as large a volume of the machine as is possible. In addition, the size distribution of the air bubbles generated by the machine is also important, but experience has shown that the proper choice of frother type and dosage generally dominates the bubble size distributions being produced.
Sufficient control of pulp agitation in the froth zone. As mentioned earlier, good mixing in the machine is important; however, equally important is that near and in the actual froth bed at the top of the machine, sufficiently smooth or quiescent pulp conditions must be maintained to ensure suspension of hydrophobed (collector coated) particles.
Efficient mass flow-mechanisms. It is also necessary in any flotation machine that appropriate provisions be made for feeding pulp into the machine and also for the efficient transport of froth concentrate and tailing slurry out of the machine.
Probably the most significant area of change in mechanical flotation machine design has been the dramatic increase in machine size. This is typified by the data ofFig. 8, which shows the increase in machine (cell) volume size that has occurred with a commonly used cell manufactured by Wemco. The idea behind this approach is that as machine size increases, both plant capital and operating costs per unit of throughput decrease.
The throughput capabilities of various cell designs will vary with flotation residence time and pulp density. The number of cells required for a given operation is determined from standard engineering mass balance calculations. In the design of a new plant, the characterization of each cell's volume and flotation efficiency is generally calculated from performing a laboratory-scale flotation on the same type of equipment on the ore in question, followed by the application of empirically derived design (scale-up) factors. Research work is currently under way to improve the understanding and performance of commercial flotation cells. Currently, flotation-cell design is primarily a proprietary function of the various cell manufacturers.
Flotation plants are built in multiple cell configurations (called banks), and the flow through various banks is adjusted in order to optimize plant recovery of the valuable as well as the valuable grade of the total recovered mass from flotation. This recovery vs grade trade-off is economically important in flotation, as increased recovery of the valuable is associated with decreased grade. For example, a 95% recovery of copper in the feed ore might give a concentrate grade of 18% Cu in the total recovered mass, while 80% Cu recovery might give a grade of 25% in the concentrate. Obviously, the higher the valuable recovery is, the higher the potential income, but if this higher recovery requires a great deal more grinding and/or expensive downstream processing (including further flotation) in order to upgrade the concentrate for metal refining such as smelting, the increase in potential recovery income may actually cause a net loss of total income. This grade-recovery optimization is generally worked out by individual flotation operators in each plant (and each mineral) and sets the operating philosophy of that plant.Figure 9 shows a typical industrial recovery vs grade trade-off curve for a copper sulfide ore containing pyrite. The higher the copper recovery is, the greater the amount of undesired pyrite contained in the concentrate.
The various banks of flotation cells in an industrial plant are given special names to denote the particular purpose of the banks. The rougher bank is the first group of cells that the pulp sees after size reduction. The goal of the roughers is to produce a concentrate with as high a recovery of valuable as possible with generally low grade of the valuable. The rejected gangue material from any bank of cells is commonly denoted as the tails or tailings. Usually, rougher tails are discarded so that valuable mineral not recovered in the rougher bank is lost. The concentrate of the rougher bank can be further concentrated, sometimes after additional grinding, in banks of cells called cleaners or recleaners. The tailings from the cleaners or recleaners can be recirculated to a bank of cells known as scavengers in order not to lose any valuable material in the upgrading process. Various banks of cells are also sometimes known by the particle size of the particular pulps being floated. Coarse particles, fine or slime particles, and middle-sized particles, denoted as middlings, can all be treated in separate banks.
As to overall capacities of flotation plants, the range is quite variable, depending on the type and value of the mineral being processed, the amount of valuable mineral in the feed ore to flotation, the degree and cost of size reduction involved, and the relative response of the valuable(s) to the flotation process. Smaller plants ranging in size from 500 to 5000 metric tons of feed per day are common, with feed materials having high amounts of valuable per ton of feed ore (>40%), such as coal, phosphate, and oxide ores. On the other hand, the sulfide minerals that are typically a small percentage of the ore (<10% and often less than 1%) require much greater capacity in order to achieve a reasonable economic return on investment. Thus, typical copper sulfide plants have capacities in the range of 20,000 to more than 60,000 metric tons of feed ore per day.
Conventional flotation machines house two functions in a single vessel: an intense mixing region where bubbleparticle collision and attachment occurs, and a quiescent region where the bubbleparticle aggregates separate from the slurry. The reactor/separator machines decouple these functions into two separate (or sometimes more) compartments. The cells are typically considered high-intensity machines due to the turbulent mixing in the reactor (see Section 12.9.5). The role of the separator is to allow sufficient time for mineralized bubbles to separate from the tailing stream which generally requires relatively short residence time (when compared to mechanical cells or columns).
Some of the earliest machine designs were of the reactor/separator-type. Figure 12.80 shows a design from a patent by Hebbard (1913). Feed slurry was mixed with entrained air in an agitation box (reactor) and flowed into the separation vessel where froth was collected as overflow. The design would be the basis for the Minerals Separation Corporation standard machine and early flotation cells used in the United States (Lynch et al., 2010).
The Davcra cell (Figure 12.81) was developed in the 1960s and is considered to be the first high-intensity machine. The cell could be thought of as a column or reactor/separator device. Air and feed slurry are contacted and injected into the tank through a cyclone-type dispersion nozzle, the energy of the jet of pulp being dissipated against a vertical baffle. Dispersion of air and collection of particles by bubbles occurs in the highly agitated region of the tank, confined by the baffle. The pulp flows over the baffle into a quiescent region designed for bubblepulp disengagement. Although not widely used, Davcra cells replaced some mechanical cleaner machines at Chambishi copper mine in Zambia, with reported lower operating costs, reduced floor area, and improved metallurgical performance.
Several attempts have been made to develop more compact column-type devices, the Jameson cell (Jameson, 1990; Kennedy, 1990; Cowburn et al., 2005) being a successful example (Figure 12.82). The Jameson cell was developed in the 1980s jointly by Mount Isa Mines Ltd and the University of Newcastle, Australia. The cell was first installed for cleaning duties in base metal operations (Clayton et al., 1991; Harbort et al., 1994), but it has also found use in coal plants and in roughing and preconcentrating duties. The original patent refers to the Jameson cell as a column method, but it can also be considered a reactor/separator machine: contact between the feed and the air stream is made using a plunging slurry jet in a vertical downcomer (the reactor), and the airslurry mixture flows downwards to discharge and disengage into a shallow pool of pulp in the bottom of a short cylindrical tank (the separator). The disengaged bubbles rise to the top of the tank to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. Air is self-aspirated (entrained) by the action of the plunging jet. The air rate is influenced by jet velocity and slurry density and level in the separator chamber.
The Jameson cell has been widely used in the coal industry in Australia since the 1990s. Figure 12.83 shows a typical cell layout where fine coal slurry feeds a central distributor which splits the stream to the downcomers. Clean coal is seen overflowing as concentrate from the separation vessel. The major advantage of the cell in this application is the ability to produce clean concentrates in one stage of operation by reducing entrainment, especially when wash water is used. It also has a novel application in copper solvent extraction/electrowinning circuits, where it is used to recover entrained organic droplets from electrolyte (Miller and Readett, 1992).
The Contact cell (Figure 12.84) was developed in the 1990s in Canada. The feed slurry is placed in direct contact with pressurized air in an external contactor which comprises a draft tube and an orifice plate. The slurryair mixture is fed from the contactor to the column-type separation vessel, where mineralized bubbles rise to form froth. Contact cells employ froth washing similar to conventional flotation columns and Jameson cells. Contact cells have been implemented in operations in North America, Africa, and Europe.
The IMHOFLOT V-Cell (Figure 12.85(a)) was developed in the 19801990s and evolved from earlier designs developed in Germany in the 19601970s (Imhof et al., 2005; Lynch et al., 2010). Conditioned feed pulp is mixed with air in an external self-aeration unit above the flotation cell. The airslurry mixture descends a downcomer pipe and is introduced to the separation vessel via a distributor box and ring pipe with nozzles that redirect the flow upward in the cell. The separation vessel is fitted with an adjustable froth crowding cone which can be used to control mass pull. The concentrate overflows to an external froth launder, while the tailings stream exits at the base of the separation vessel. The V-Cell has been used to float sulfide and oxide ores with the largest operation being an iron ore application (Imhof et al., 2005).
The IMHOFLOT G-Cell (Figure 12.85(b)) was introduced in 2001 and employs the same external self-aerating unit as the V-Cell. The airslurry mixture which exits the aeration unit is fed to an external distributor box (located above the separation vessel) where pulp is split and fed to the separation vessel tangentially via feed pipes. The cell is unusual as an internal launder located at the center of the vessel collects froth. The centrifugal motion of the slurry enhances froth separation with residence times being ca. 30s.
The Staged Flotation Reactor (SFR) (Figure 12.86) is a recent development in the minerals industry. By sequencing the three processesparticle collection, bubble/slurry disengagement, and froth recoveryand assigning each to a purpose-built chamber, the SFR aims to optimize each of the three processes independently.
The SFR incorporates an agitator in the first (collection) chamber designed to provide high energy intensity (kWm3) and induce multiple particle passes through the high shear impeller zone, hence giving high collection efficiency. Slurry flows by gravity through the reactor stages, that is, there is no need to apply agitation to suspend solids, only for particle collection. As such, impeller speed can be adjusted online in correlation with desired recovery without sanding. The second tank is designed to deaerate the slurry (bubble disengagement) and rapidly recover froth to the launder without dropback. The froth recovery unit is tailored for use of wash water and for high solids flux. Efficient particle collection and high froth recovery translate into fewer, smaller cells, resulting in a smaller footprint and building height, with lower power consumption, and the potential for good selectivity in both roughing and cleaning applications.
Induced air flotation machines have gained a degree of popularity within certain sections of the minerals processing industry because of their ability to produce small bubbles at relatively high energy efficiency. The most common of such machines is the Jameson Cell. A downcomer protrudes out of the bubbly liquid in which is housed a plunging jet. Because this jet is at high velocity the pressure within the downcomer is low due to the Bernoulli equation, and air is induced into the downcomer creating a plume of bubbles within the liquid, which rise to form a foam. There are major problems with operating Jameson Cells because their high demand for surfactant causes downstream residual frother issues. (It is noted, as an aside, that frother strippers are being developed to remove residual frother in flotation circuits, and these are identical to foam fractionation units.) Notwithstanding that Jameson Cell technology has failed to live up to its promise, it has been successfully used as a pilot-scale foam reactor to effect the autothermal thermophilic aerobic digestion (ATAD) of high strength wastewater sludge produced at a chicken processing factory. The advantage that induced gas systems have over alternative pneumatic foam systems is their very high gasliquid surface area per unit volume of foam due to their small bubbles. This feature of the foams would also be an advantage in foam fractionation because it creates high flux of gasliquid surface. However, to the authors knowledge, no attempt has ever been made to use induced gas systems as foam fractionators.
The Denver DR flotation machine, which is an example of a typical froth flotation unit used in the mining industry, is illustrated in Figure 1.47. The pulp is introduced through a feed box and is distributed over the entire width of the first cell. Circulation of the pulp through each cell is such that, as the pulp comes into contact with the impeller, it is subjected to intense agitation and aeration. Low pressure air for this purpose is introduced down the standpipe surrounding the shaft and is thoroughly disseminated throughout the pulp in the form of minute bubbles when it leaves the impeller/diffuser zone, thus assuring maximum contact with the solids, as shown in Figure 1.47. Each unit is suspended in an essentially open trough and generates a ring doughnut circulation pattern, with the liquid being discharged radially from the impeller, through the diffuser, across the base of the tank, and then rising vertically as it returns to the eye of the impeller through the recirculation well. This design gives strong vertical flows in the base zone of the tank in order to suspend coarse solids and, by recirculation through the well, isolates the upper zone which remains relatively quiescent.
Froth baffles are placed between each unit mechanism to prevent migration of froth as the liquid flows along the tank. The liquor level is controlled at the end of each bank section by a combination of weir overflows and dart valves which can be automated. These units operate with a fully flooded impeller, and a low pressure air supply is required to deliver air into the eye of the impeller where it is mixed with the recirculating liquor at the tip of the air bell. Butterfly valves are used to adjust and control the quantity of air delivered into each unit.
Each cell is provided with an individually controlled air valve. Air pressure is between 108 and 124 kN/m2 (7 and 23 kN/m2 gauge) depending on the depth and size of the machine and the pulp density. Typical energy requirements for this machine range from 3.1 kW/m3 of cell volume for a 2.8 m3 unit to 1.2 kW/m3 for a 42 m3 unit.
In the froth flotation cell used for coal washing, illustrated in Figure 1.48, the suspension contains about 10 per cent of solids, together with the necessary reagents. The liquid flows along the cell bank and passes over a weir, and directly enters the unit via a feed pipe and feed hood. Liquor is discharged radially from the impeller, through the diffuser, and is directed along the cell base and recirculated through ports in the feed hood. The zone of maximum turbulence is confined to the base of the tank; a quiescent zone exists in the upper part of the cell. These units induce sufficient air to ensure effective flotation without the need for an external air blower.
Most of the industrial flotation machines used in the coal industry are mechanical, conventional cells. These machines consist of a series of agitated tanks (usually 48 cells) through which fine coal slurry is passed. The agitators are used to ensure that larger particles are kept in suspension and to disperse air that enters down through the rotating shaft assembly (Fig. 11.13). Air is either injected into the cell using a blower or drawn into the cell by the negative pressure created by the rotating impeller. For coal flotation, trough designs that permit open flow between cells along the bank are more common than cell-to-cell designs that are separated by individual weirs.
Some of the major manufacturers of flotation equipment include Wemco (FLSmidth), Metso, Svedala, and Outokumpu. The commercial units are very similar in basic design and function, although some slight variations exist in terms of cell geometry and impeller configuration. Machines with large specific surface areas are generally preferred for coal flotation, due to the fast flotation kinetics of coal and the large froth solids loadings. Flotation machines with individual cell volumes of up to 28m3 are commonly used due to advantages in terms of capital, operating and maintenance costs. Some manufacturers also offer tank machines, which consist of relatively short cylindrical tanks equipped with conventional impellers. The simplified structural design, which allows these machines to be much larger, can offer significant savings in terms of capital and power costs for some installations. Tank cells with volumes as large as 100m3 are already in operation at coal plants in Australia.
Unlike conventional, mechanically agitated flotation machines, which tend to use relatively shallow rectangular tanks, column cells used in the coal industry are usually tall vessels with heights typically ranging from 7 to 16m depending on the application. Unlike conventional flotation machines, columns do not use mechanical agitation and are typically characterized by an external sparging system, which injects air into the bottom of the column cell. The absence of intense agitation promotes higher degrees of selectivity and can aid in the recovery of coarse particles.
In general, feed slurry enters the column at one or more feed points located in the upper third of the column body and descends against a rising swarm of fine bubbles generated by the air sparging system (Fig. 11.14). Hydrophobic particles that collide with, and attach to, the bubbles rise to the top of the column, eventually reaching the interface between the pulp (collection zone) and the froth (cleaning zone). The location of this interface, which can be adjusted by the operator, is held constant by means of an automatic control loop that regulates a valve on the column tailings line. Varying the location of the interface will increase or decrease the height of the froth zone. The froth is transported from the froth zone into the product launder via mass action.
Methods of sparging in columns are numerous and include air lances, porous tubes, eductors, static mixers, and Cavitation-TubesTM. The air rate used in a column is selected according to the feed rate and concentrate-production requirements. This parameter typically has the largest effect on the operating point of the column with respect to the ash/yield curve. The bubbles generated by the air sparging system are sized to provide the maximum amount of bubble surface area given a constant energy input. In other words, the designs of the various sparging devices are engineered to provide the smallest size and largest number of bubbles possible.
For an equivalent volumetric capacity, the cross-sectional surface area of a column cell is much smaller than that of a conventional cell. This reduced area is beneficial for promoting froth stability and allowing deep froth beds to be formed. This is an important aspect of column flotation, as a deep froth bed facilitates froth washing for the removal of unwanted impurities from the float product. Wash water, added at the top of the column, percolates through the froth zone displacing dirty process water and non-selectively entrained particles trapped between the bubbles. In addition, froth wash water serves to stabilize and add mobility to the froth. Sufficient water must be added to ensure that all of the feed water that would otherwise normally report to the froth product is replaced with fresh or clarified water. It has been reported that less than 1% of the feed pulp and associated clays will report to the froth in a well-operated column (Luttrell et al., 1999). The ability to maintain and wash a deep froth layer is the main reason cited for the improved product grades when comparing column cells to conventional cells.
In contrast, conventional mechanical cells do not operate with deep froths. Therefore, these devices allow some portion of the ultrafine mineral slimes to be recovered with the water that reports to the froth. Consequently product quality is reduced by this non-selective hydraulic conveyance (i.e., entrainment) of gangue into the product launder. In fact, fine particles (<0.045mm) have a tendency to report to the froth concentrate in direct proportion to the amount of product water recovered. As such, the flotation operator is often forced to make the decision to either pull hard on the cells to maintain yield (e.g., wet froth), or run the cells less aggressively to maintain grade (e.g., dry froth).
The primary advantage of utilizing wash water is the ability to provide a superior product grade when compared to conventional flotation processes. This capability is illustrated by the test data summarized in Fig. 11.15, which compares column flotation technology with an existing bank of conventional cells. As shown, the separation data for the column cells utilizing wash water are far superior to those obtained from the conventional flotation bank. In fact, the data for the column cells tend to fall just below the separation curve predicted by release analysis (Dell et al., 1972). A release analysis is an indication of the ultimate flotation performance and is often regarded as wash-ability for flotation. This figure suggests that columns provide a level of performance that would be difficult to achieve even after multiple stages of cleaning by conventional machines.
There are a significant number of full-scale column installations currently in commercial service around the world. The most popular brands of columns include the CPT CoalPro (Eriez), Jameson, and Microcel columns. Although the Jameson cell does not have the traditional column geometry, it is included since it typically uses wash water to improve ash rejection. Details related to the specific design features of the various column technologies are available in the literature (McKay et al., 1988; Finch and Dobby, 1990; Yoon et al., 1992; Manlapig et al., 1993; Davis et al., 1995; Rubinstein, 1995; Wyslouzil, 1997). The primary difference between the various columns used in the coal industry is the type of air sparging system employed. These include porous bubblers, static mixers, and dynamic air injectors. Details related to the features and operation of these systems have been discussed extensively in the literature (Dobby and Finch, 1986a; Xu and Finch, 1989; Huls et al., 1991; Groppo and Parekh, 1992; Yoon et al., 1992; Finch, 1995). Ideally, the spargers should produce small, uniformly sized bubbles at a desired aeration rate. Other factors, such as equipment costs, mechanical reliability, wear resistance, and serviceability also need to be carefully considered prior to selecting an industrial sparging system.
Due to economy of scale, recent trends in the coal industry have shifted away from the installation of large numbers of smaller units toward fewer, large units with diameters up to 5m or more. Although most column installations involve the treatment of particles finer than 0.150mm, several recent column operations have been installed to treat coarser particles, such as minus 1mm feeds or deslimed 0.1500.045mm feeds. Additionally, a move to more economical cells in terms of energy efficiency has been realized as manufacturers focus on the generation of the required air bubble dispersions while using significantly less power than traditional approaches. One such device is the Eriez StackCell, which utilizes both pre-aeration methods in conjunction with traditional froth washing (Davis et al., 2011) to maximize efficiency with regard to both installation and operating cost.
The two most important requirements of laboratory flotation machines are reproducibility and performance similar to commercial operations. These two criteria are not always satisfied. The basic laboratory machines are scaled down replicas of commercial machines such as Denver, Wemco and Agitair. In the scale down, there are inevitable compromises between simplification of manufacture and attempts to simulate full scale performance. There are scaling errors, for example, in the number of impeller and stator blades and various geometric ratios. Reproducibility in semi-batch testing requires close control of impeller speed, air flow rate, pulp level and concentrate removal.
Until now, deaeration tanks always had to be placed underneath the flotation machine and also frequently in the cellar of a facility in order to ensure a sufficient height difference for the conveyance of foam. In addition, the tanks are open on top and can overflow with excess foam. That is now a thing of the past with the Deaeration Foam Pump (DFP) 4000. The new pump can be linked directly to the deinking machine and forms a clean and closed disposal system. Because it can be placed at the same level as the flotation cells, the entire flotation system saves more space than previous systems. A cellar or an additional floor height for the flotation is no longer required. The deaeration results are very impressive with the DFP 4000 from Voith Paper. The air content of the foam mass is reduced when passing through the pump from 80% to an average of 8%. Conventional deaeration systems offer approximately 12%. In addition, by using the DFP 4000, upstream foam destroyers, downstream long piping as well as pumps with high head pressures to overcome the floor height can be dispensed. With the DFP 4000, it is possible to deaerate and convey the foam, which is loaded with inks and other impurities, within a single machine. As a compact unit, it fully replaces the foam destroyer, foam tank stirring unit, and pump of previous deaeration systems. This means a clear reduction in investment costs for the tank, stirring unit, pipes, pumps, and floor space.
The DFP 4000, developed by Voith, is a compact unit that integrates several elements of the flotation deinking system. This combines the pump and deaeration machine into one unit. The deaeration foam pump replaces the foam destroyer, foam tank, stirring unit, and pump and costs less than the current suite of equipment. The DFP 4000 achieves better deaeration of the foam than conventional systems.
The DFP 4000 has two parts. In the upper part, foam is predeaerated by a mechanical foam destroyer. In the lower part, centrifugal force produced by a quick rotational movement further deaerates the foam. The resulting low-air-content suspension is brought to the required pressure so that it can be conveyed out of the machine to the next process stage. The air released during deaeration is conveyed out of the machine through a special air chamber on the side so that the airflow does not prevent the foam entering from above (Dreyer,2010).
The new pump can be linked directly to the deinking machine, forming a clean and closed disposal system. Because the deaeration pump can be placed at the same level as the flotation cells, the entire system requires less space than previous systems, so a cellar (or additional floor height) is no longer required to accommodate the system. When the foam mass passes through the DFP 4000, the foams air content is reduced from 80% to an average of 8% (Voith,2011a). Conventional deaeration systems reduce the air content to approximately 12%. The first DFP 4000 operating in a paper mill has been in service since September 2009 (Dreyer,2010). The benefits of the DFP 4000 are summarized in Table11.9 (Dreyer,2010; Voith,2011a).
Batch testing has been carried out using a specially designed 21 tumbler for mixing, and a standard Denver flotation machine for separation. A typical charge of the soil sample ranged from 200 to 600g, and the amount of coal varied depending on the contaminant concentration.
Figure 1 shows the block diagram of the 6T/day continuous unit. A slurry of contaminated soil and coal is fed at optimal solids concentration to a specially designed tumbler. In the front section of the tumbler, as a result of rotary motion, the solids are mixed and dispersed. In another section of the tumbler, layering, compaction and abrasion take place. After being discharged from the tumbler, the contents are screened into two streams. The 1mm particle size stream is directed to a high shear mixer where the oil-wetted coal particles are conditioned. The slurry is then transfered to flotation cells, where the coal microagglomerates, in the form of froth, are separated from clean soil. To facilitate dewatering and improve handleability of the combustible product, the froth can be subsequently fed into the low shear mixer for further agglomeration.
Flotation has progressed and developed over the years; recent trends to achieve better liberation by fine grinding have intensified the search for more advanced means of improving selectivity. This involves not only more selective flotation agents but also better flotation equipment. Since the froth product in conventional flotation machines contains entrained fine gangue, which is carried into the froth with feed water, the use of froth spraying was suggested in the late 1950s to eliminate this type of froth contamination. The flotation column patented in Canada in the early 1960s and marketed by the Column Flotation Company of Canada, Ltd., combines these ideas in the form of wash water supplied to the froth. The countercurrent wash water introduced at the top of a long column prevents the feed water and the slimes that it carries from entering an upper layer of the froth, thus enhancing selectivity.
The microbubble flotation column (Microcel) developed at Virginia Tech is based on the basic premise that the rate (k) at which fine particles collide with bubbles increases as the inverse cube of the bubble size (Db), i.e., k1/Db3. In the Microcel, small bubbles in the range of 100500m are generated by pumping a slurry through an in-line mixer while introducing air into the slurry at the front end of the mixer. The microbubbles generated as such are injected into the bottom of the column slightly above the section from which the slurry is with drawn for bubble generation. The microbubbles rise along the height of the column, pick up the coal particles along the way, and form a layer of froth at the top section of the column. Like most other columns, it utilizes wash water added to the froth phase to remove the entrained ash-forming minerals. Advantages of the Microcel are that the bubble generators are external to the column, allowing for easy maintenance, and that the bubble generators are nonplugging. An 8-ft diameter column uses four 4-in. in-line mixers to produce 56 tons of clean coal from a cyclone overflow containing 50% finer than 500 mesh.
Another interesting and quite different column was developed at Michigan Tech. It is referred to as a static tube flotation machine, and it incorporates a packed-bed column filled with a stack of corrugated plates. The packing elements arranged in blocks positioned at right angles to each other break bubbles into small sizes and obviate the need for a sparger. Wash water descends through the same flow passages as air (but countercurrently) and removes entrained particles from the froth product. It was shown in both the laboratory and the process demonstration unit that this device handles extremely well fine below 500-mesh material.
Another novel concept is the Air-Sparged Hydrocyclone developed at the University of Utah. In this device, the slurry fed tangentially through the cyclone header into the porous cylinder to develop a swirl flow pattern intersects with air sparged through the jacketed porous cylinder. The froth product is discharged through the overflow stream.
The process is carried out in a flotation cell or tank, of which there are two basic types, mechanical and pneumatic. Within each of these categories, there are two subtypes, those that operate as a single cell, and those that are operated as a series or bank of cells. A bank of cells (Fig. 8) is preferred because this makes the overall residence times more uniform (i.e., more like plug flow), rather than the highly diverse residence times that occur in a single (perfectly mixed) tank.
FIGURE 8. Flotation section of a 80,000t/d concentrating plant, showing the arrangement of the flotation cells into banks. A small part of the grinding section can be seen through the gap in the wall. [Courtesy Joy Manufacturing Co.]
The purpose of the flotation cell is to attach hydrophobic particles to air bubbles, so that they can float to the surface, form a froth, and can be removed. To do this, a flotation machine must maintain the particles in suspension, generate and disperse air bubbles, promote bubbleparticle collision, minimize bypass and dead spaces, minimize mechanical passage of particles to the froth, and have sufficient froth depth to allow nonhydrophobic (hydrophilic) particles to return to the suspension.
Pneumatic cells have no mechanical components in the cell. Agitation is generally by the inflow of air and/or slurry, and air bubbles are usually introduced by an injector. Until comparatively recently, their use was very restricted. However, the development of column flotation has seen a resurgence of this type of cell in a wider, but still restricted, range of applications. While the total volume of cell is still of the same order as that of a conventional mechanical cell, the floor space and energy requirements are substantially reduced. But the main advantage is that the cell provides superior countercurrent flow to that obtained in a traditional circuit (see Fig. 11), and so they are now often used as cleaning units.
Mechanical cells usually consist of long troughs with a series of mechanisms. Although the design details of the mechanisms vary from manufacturer to manufacturer, all consist of an impeller that rotates within baffles. Air is drawn or pumped down a central shaft and is dispersed by the impeller. Cells also vary in profile, degree of baffling, the extent of walling between mechanisms, and the discharge of froth from the top of the cell.
Selection of equipment is based on performance (represented by grade and recovery), capacity (metric tons per hour per cubic meter); costs (including capital, power, maintenance), and subjective factors.
More ores are treated using froth flotation cells than by any other single machines or process. Non-metallics as well as metallics now being commercially recovered include gold, silver, copper, lead, zinc, iron, manganese, nickel, cobalt, molybdenum, graphite, phosphate, fluorspar, barite, feldspar and coal. Recent flotation research indicates that any two substances physically different, but associated, can be separated by flotation under proper conditions and with the correct machine and reagents. The DRflotation machine competes with Wemco and Outotec (post-outokumpu) flotation cells but are all similar is design. How do flotation cells and machinework for themineral processing industry will be better understood after you read on.
While many types of agitators and aerators will make a flotation froth and cause some separation, it is necessary to have flotation cells with the correct fundamental principles to attain high recoveries and produce a high grade concentrate. The Sub-A (Fahrenwald) Flotation Machines have continuously demonstrated their superiority through successful performance. The reliability and adaptations to all types of flotation problems account for the thousands of Sub-A Cells in plants treating many different materials in all parts of the world.
The design of Denver Sub-A flotation cells incorporates all of the basic principles and requirements of the art, in addition to those of the ideal flotation cell. Its design and construction are proved by universal acceptance and its supremacy is acknowledged by world-wide recognition and use.
1) Mixing and Aeration Zone:The pulp flows into the cell by gravity through the feed pipe, dropping directly on top of the rotating impeller below the stationary hood. As the pulp cascades over the impeller blades it is thrown outward and upward by the centrifugal force of the impeller. The space between the rotating blades of the impeller and the stationary hood permits part of the pulp to cascade over the impeller blades. This creates a positive suction through the ejector principle, drawing large and controlled quantities of air down the standpipe into the heart of the cell. This action thoroughly mixes the pulp and air, producing a live pulp thoroughly aerated with very small air bubbles. These exceedingly small, intimately diffused air bubbles support the largest number of mineral particles.
This thorough mixing of air, pulp and reagents accounts for the high metallurgical efficiency of the Sub-A (Fahrenwald) Flotation Machine, and its correct design, with precision manufacture, brings low horsepower and high capacity. Blowers are not needed, for sufficient air is introduced and controlled by the rotating impeller of the Denver Sub-A. In locating impeller below the stationary hood at the bottom of the cell, agitating and mixing is confined to this zone.
2) Separation Zone:In the central or separation zone the action is quite and cross currents are eliminated, thus preventing the dropping or knocking of the mineral load from the supporting air bubble, which is very important. In this zone, the mineral-laden air bubbles separate from the worthless gangue, and the middling product finds its way back into the agitation zone through the recirculation holes in the top of the stationary hood.
3) Concentrate Zone:In the concentrate or top zone, the material being enriched is partially separated by a baffle from the spitz or concentrate discharge side of the machine. The cell action at this point is very quiet and the mineral-laden concentrate moves forward and is quickly removed by the paddle shaft (note direct path of mineral). The final result is an unusually high grade concentrate, distinctive of the Sub-A Cell.
A flotation machine must not only float out the mineral value in a mixture of ground ore and water, but also must keep the pulp in circulation continuously from the feed end to the discharge end for the removal of the froth, and must give the maximum treatment positively to each particle.
It is an established fact that the mechanical method of circulating material is the most positive and economical, particularly where the impeller is below the pulp. A flotation machine must not only be able to circulate coarse material (encountered in every mill circuit), but also must recirculate and retreat the difficult middling products.
In the Denver Sub-A due to the distinctive gravity flow method of circulation, the rotating impeller thoroughly agitates and aerates the pulp and at the same time circulates this pulp upward in a straight line, removing the mineral froth and sending the remaining portion to the next cell in series. No short circuiting through the machine can thus occur, and this is most important, for the more treatments a particle gets, the greater the chances of its recovery. The gravity flow principle of circulation of Denver Sub-A Flotation Cell is clearly shown in the illustration below.
There are three distinctive advantages of theSub-A Fahrenwald Flotation Machines are found in no other machines. All of these advantages are needed to obtain successful flotation results, and these are:
Coarse Material Handled:Positive circulation from cell to cell is assured by the distinctive gravity flow principle of the Denver Sub-A. No short circuiting can occur. Even though the ore is ground fine to free the minerals, coarse materials occasionally gets into the circuit, and if the flotation machine does not have a positive gravity flow, choke-ups will occur.
In instances where successful metallurgy demands the handling of a dense pulp containing an unusually large amount of coarse material, a sand relief opening aids in the operation by removing from the lower part of the cell the coarser functions, directing these into the feed pipe and through the impeller of the flowing cell. The finer fraction pass over the weir overflow and thus receive a greater treatment time. In this manner short-circuiting is eliminated as the material which is bled through the sand relief opening again receives the positive action of the impeller and is subjected to the intense aeration and optimum flotation condition of each successive cell, floating out both fine and coarse mineral.
No Choke-Ups or Lost Time:A Sub-A flotation cell will not choke-up, even when material as coarse as is circulated, due to the feed and pulp always being on top of the impeller. After the shutdown it is not necessary to drain the machine. The stationary hood and the air standpipe during a shutdown protects the impeller from sanding-up and this keeps the feed and air pipes always open. Denver Sub-A flotation operators value its 24-hour per day service and its freedom from shutdowns.
This gravity flow principle of circulation has made possible the widespread phenomenal success of a flotation cell between the ball mill and classifier. The recovery of the mineral as coarse and as soon as possible in a high grade concentrate is now highly proclaimed and considered essential by all flotation operators.
Middlings Returned Without Pumps:Middling products can be returned by gravity from any cell to any other cell. This flexibility is possible without the aid of pumps or elevators. The pulp flows through a return feed pipe into any cell and falls directly on top of the impeller, assuring positive treatment and aeration of the middling product without impairing the action of the cell. The initial feed can also enter into the front or back of any cell through the return feed pipe.
Results : It is a positive fact that the application of these three exclusive Denver Sub-A advantages has increased profits from milling plants for many years by increasing recoveries, reducing reagent costs, making a higher grade concentrate, lowering tailings, increasing filter capacities, lowering moisture of filtered concentrate and giving the smelter a better product to handle.
Changes in mineralized ore bodies and in types of minerals quickly demonstrate the need of these distinctive and flexible Denver Sub-A advantages. They enable the treatment of either a fine or a coarse feed. The flowsheet can be changed so that any cell can be used as a rougher, cleaner, or recleaner cell, making a simplified flowsheet with the best extraction of mineral values.
The world-wide use of the Denver Sub-A (Fahrenwald) Flotation Machine and the constant repeat orders are the best testimonial of Denver Sub-A acceptance. There are now over 20,000 Denver Sub-A Cells in operation throughout the world.
There is no unit so rugged, nor so well built to meet the demands of the process, as the Denver Sub-A (Fahrenwald) Flotation Machine. The ruggedness of each cell is necessary to give long life and to meet the requirements of the process. Numerous competitive tests all over the world have conclusively proved the real worth of these cells to many mining operators who demand maximum result at the lower cost.
The location of the feed pipe and the stationary hood over the rotating impeller account for the simplicity of the Denver Sub-A cell construction. These parts eliminates swirling around the shaft and top of the impeller, reduce power load, and improve metallurgical results.
TheSub-A Operates in three zones: in bottom zone, impeller thoroughly mixes and aerates the pulp, the central zone separates the mineral laden particles from the worthless gangue, and in top zone the mineral laden concentrate high in grade, is quickly removed by the paddle of a Denver Sub-A Cell.
A Positive Cell Circulation is always present in theSub-A (Fahrenwald) Flotation Machine, the gravity flour method of circulating pulp is distinctive. There is no short circulating through the machine. Every Cell must give maximum treatment, as pulp falls on top of impeller and is aerated in each cell repeatedly. Note gravity flow from cell to cell.
Choke-Ups Are Eliminated in theSub-A Cell, even when material as coarse as is handled, due to the gravity flow principle of circulation. After shutdown it is not necessary to drain the machine, as the stationary hood protects impeller from sanding up. See illustration at left showing cell when shut down.
No Bowlers, noair under pressure is required as sufficient air is drawn down the standpipe. The expense and complication of blowers, air pipes and valves are thus eliminated. The standpipe is a vertical air to the heart of the Cell, the impeller. Blower air can be added if desired.
The Sub-A Flexibility allows it tobe used as a rougher, cleaner or recleaner. Rougher or middling product can be returned to the front or back of any cell by gravity without the use of pumps or elevators. Cells can be easily added when required. This flexibility is most important in operating flotation MILLS.
Pulp Level Is Controlled in each Sub-A Flotation Cell as it has an individual machine with its own pulp level control. Correct flotation requires this positive pulp level control to give best results in these Cells weir blocks are used, but handwheel controls can be furnished at a slight increase in cost. Note the weir control in each cell.
High Grade Concentrate caused by thequick removal of the mineral forth in the form of a concentrate increases the recovery. By having an adjustment paddle for each Sub-A Cell, quick removal of concentrate is assured, Note unit bearing housing for the impeller Shaft and Speed reducer drive which operates the paddle for each cell
Has Fewer Wearing Parts because Sub-A Cells are built for long, hard service, and parts subject to wear are easily replaced at low cost. Molded rubber wearing plates and impellers are light in weight give extra long life, and lower horsepower. These parts are made under exact Specifications and patented by Denver Equipment Co.
TheRugged Construction of theSub-A tank is made of heavy steel, and joints are welded both inside and out. The shaft assemblies are bolted to a heavy steel beam which is securely connected to the tank. Partition plates can be changed in the field for right or left hand machine. Right hand machine is standard.
The Minerals Separation or M.S. Sub-aeration cells, a section of which is shown in Fig. 32, consists essentially of a series of square cells with an impeller rotating on a vertical shaft in the bottom of each. In some machines the impeller is cruciform with the blades inclined at 45, the top being covered with a flat circular plate which is an integral part of the casting, but frequently an enclosed pump impeller is used with curved blades set at an angle of 45 and with a central intake on the underside ; both patterns are rotated so as to throw the pulp upwards. Two baffles are placed diagonally in each cell above the impeller to break up the swirl of the pulp and to confine the agitation to the lower zone. Sometimes the baffles are covered with a grid consisting of two or three layers each composed of narrow wood or iron strips spaced about an inch apart. The sides and bottom of the cells in the lower or agitation zone are protected from wear by liners, which are usually made of hard wood, but which can, if desired, consist of plates of cast-iron or hard rubber. The section directly under the impeller is covered with a circular cast-iron plate with a hole in the middle for the admission of pulp and air. The hole communicates with a horizontal transfer passage under the bottom liner, through which the pulp reaches the cell. Air is introduced into each cell through a pipe passing through the bottom and delivering its supply directly under the impeller. A low-pressure blower is provided with all machines except the smallest, of which the impeller speed is fast enough to draw in sufficient air by suction for normal requirements.
The pulp is fed to the first cell through a feed opening communicating with the transfer passage, along which it passes, until, at the far end, it is drawn up through the hole in the bottom liner by the suction of the impeller and is thrown outwards by its rotation into the lower zone. The square shape of the cell in conjunction with the baffles converts the swirl into a movement of intense agitation, which breaks up the air entering at the same time into a cloud of small bubbles, disseminating them through the pulp. The amount of aeration can be accurately regulated to suit the requirements of each cell by adjustment of the valve on its air pipe.
Contact between the bubbles and the mineral particles probably takes place chiefly in the lower zone. The pumping action of the impeller forces the aerated pulp continuously past the baffles into the upper and quieter part of the cell. Here the bubbles, loaded with mineral, rise more or less undisturbed, dropping out gangue particles mechanically entangled between them and catching on the way up a certain amount of mineral that has previously escaped contact. The recovery of the mineral in this way can be increased at the expense of the elimination of the gangue by increasing the amount of aeration. The froth collects at the top of the cell and is scraped by a revolving paddle over the lipat the side into the concentrate launder. The pulp, containing the gangue and any mineral particles not yet attached to bubbles, circulates to some extent through the zone of agitation, but eventually passes out through a slot situated at the back of the cell above the baffles and flows thence over the discharge weir. The height of the latter is regulated by strips of wood or iron and governs the level of the pulp in the cell. The discharge of each weir falls by gravity into the transfer passage under the next cell and is drawn up as before by the impeller. The pulp passes in this way through the whole machine until it is finally discharged as a tailing, the froth from each cell being drawn off into the appropriate concentrate launder.
No pipes are normally fitted for the transference of froth or other middling product back to the head of the machine or to any intermediate point. Should this be necessary, however, the material can be taken by gravity to the required cell through a pipe, which is bent at its lower end to pass under the bottom liner and project into the transfer passage, thus delivering its product into the stream of pulp that is being drawn up by the impeller
Particulars of the various sizes of M.S. Machines are given in Table 21. It should be noted that the size of a machine is usually defined by the diameter of its impeller ; for instance, the largest one would be described as a 24-inch machine.
The Sub-A Machine, invented by A. W. Fahrenwald and developed in many respects as an improvement in the Minerals Separation Machine, from which it differs considerably in detail, particularly in the method of aerating the pulp, although the principle of its action is essentially the same. Its construction can be seen from Figs. 33 and 34.
In common with the M.S. type of machine, it consists of a series of square cells fitted with rotating impellers. Each cell, however, is of unit construction, a complete machine being built up by mounting the required number of units on a common foundation and connecting up the pipes which transfer the pulp from one cell to the next. The cells are constructed of welded steel. The impeller, which can be rubber-lined,if required, carries six blades set upright on a circular dished disc, and is securely fixed to the lower end of the vertical driving shaft. It is covered with a stationary hood, to which are attached a stand-pipe, a feed pipe, and the middling return pipes. The underside of the hood is fitted with a renewable liner of rubber or cast-iron. The pulp, entering the first cell through the feed pipe and sometimes through the middling pipes, falls on to the impeller, the rotation of which throws it outwards into the bottom zone of agitation. The suction effect due to the rotationof the impeller draws enough air down the standpipe to supply the aeration necessary for normal operation. A portion of the pulp, cascading over the open tops of the impeller blades, entraps and breaks up the entrained air, the resulting spray-like mixture being then thrown out into the lower zone of agitation, where it is disseminated through the pulp as a cloud of fine bubbles. Should this amount of aeration be insufficient, air can be blown in under slight pressure through a hole near the top of the stand-pipe, in which case a rubber bonnet is fastenedto the lower bearing and clamped round the top of the stand-pipe so as to seal the supply from the atmosphere.
The bottom part of the cell is protected from wear by renewable cast-iron or rubber liners. Four vertical baffles, placed diagonally on the top of the hood, break up the swirl of the pulp and intensify theagitation in the lower zone. The pumping action of the impeller combined with the rising current of air bubbles carries the pulp to the quieter upper zone, where the bubbles, already coated with mineral, travel upwards, drop out many of the gangue particles which may have become entangled with them, and finally collect on the surface of the pulp as a mineralizedfroth. One side of the cell is sloped outwards so as to form, in conjunction with a vertical baffle, a spitzkasten-shaped zone of quiet settlement, where any remaining particles of gangue that have been caught and held between the bubbles are shaken out of the froth as it flows to the overflow lip at the front of the cell. The baffle prevents rising bubbles from entering the outer zone, thus enabling the gangue material released from the froth to drop down unhindered into the lower zone. A revolving paddle scrapes the froth past the overflow lip into the concentrate launder.
Should the machine be required to handle more than the normal volume of froth, it is built with a spitzkasten zone on both sides of the cell. For the flotation of ores containing very little mineral the spitzkasten is omitted so as to crowd the froth into the smallest possible space, the front of the cell being made vertical for the purpose.
Circulation of the pulp through the lower zone of agitation is maintained by means of extra holes at the base of the stand-pipe on a level with the middling return pipes. An adjustable weir provides for the discharge of the pulp to the next cell, which it enters through a feed-pipe as before. Below the weir on a level with the hood is a small sand holeand pipe through which coarse material can pass direct to the next cell without having to be forced up over the weir. The same process is repeated in each cell of the series, the froth being scraped over the lip of the machine, while the pulp passes from cell to cell until it is finally discharged as a tailing from the last one. The middling pipes make it an easy matter for froth from any section of the machine to be returned if necessary to any cell without the use of pumps.
Table 22 gives particulars of the sizes and power requirements of Denver Sub-A Machines and Table 23 is an approximate guide to their capacities under different conditions. The number of cells needed
Onemethod of driving the vertical impeller shafts of M.S. Subaeration or Denver Sub-A Machines is by quarter-twist belts from a horizontal lineshaft at the back of the machine, the lineshaft being driven in turn by a belt from a motor on the ground. This method is not very satisfactory according to modern standards, firstly, because the belts are liable to stretch and slip off, and, secondly, because adequate protection againstaccidents due to the belts breaking is difficult to provide without making the belts themselves inaccessible. A more satisfactory drive, with which most M.S. Machines are equipped, consists of a lineshaft over the top of the cells from which each impeller is driven through bevel gears. The lineshaft can be driven by a belt from a motor on the ground, by Tex- ropes from one mounted on the frame work of the machine, or by direct coupling to a slow-speed motor. This overhead gear drive needs careful adjustment and maintenance. Although it may run satisfactorily for years, trouble has been experienced at times, generally in plants where skilled mechanics have not been available. The demand for something more easily adjusted led to the development of a special form of Tex-rope drive which is shown in Fig. 35. Every impeller shaft is fitted at the top with a grooved pulley, which is driven by Tex-ropes from a vertical motor. This method is standard on Denver Sub-A Machines, and M.S. Machines are frequently equipped with it as well, but the former type are not made with the overhead gear drive except to special order.
The great advantage of mechanically agitated machines is that every cell can be regulated separately, and that reagents can be added when necessary at any one of them. Since, as a general rule, the most highly flocculated mineral will become attached to a bubble in preference to a less floatable particle, in normal operation the aeration in the first few cells of a machine should not be excessive ; theoretically there should be no more bubbles in the pulp than are needed to bring up the valuable minerals. By careful control of aeration it should be possible for the bulk of the minerals to be taken off the first few cells at the feed end of the machine in a concentrate rich enough to be easily cleaned, and sometimes of high enough grade to be sent straight to the filtering section as a finished product. The level of the pulp in these cells is usually kept comparatively low in order to provide a layer of froth deep enough to give entangled particles of gangue every chance of dropping out, but it must not be so low that the paddles are prevented from skimming off the whole of the top layer of rich mineral. Towards the end of the machine a scavenging action is necessary to make certain that the least possible amount of valuable mineral escapes in the tailing, for which purpose the gates of the discharge weirs are raised higher than at the feed end, and the amountof aeration may have to be increased. The froth from the scavenging cells is usually returned to the head of the machine, the middling pipes of the Denver Sub-A Machine being specially designed for such a purpose. The regulation of the cleaning cells is much the same as that of the first few cells of the primary or roughing machine, to the head of which the tailing from the last of the cleaning cells is usually returned.
A blower is sometimes required with the M.S. Subaeration Machine. Since each cell is fitted with an air pipe and valve, accurate regulation of aeration is a simple matter. The Denver Sub-A, Kraut, and Fagergren Machines, however, are run without blowers, enough air being drawn into the machines by suction.
In the Geco New-Cell Flotation Cellthe pneumatic principle is utilized in conjunction with an agitating device. The machine, which is illustrated in Fig. 44, consists of a trough or cell made of steel or wood, whichever is more convenient, through the bottom of which projects a series of air pipes fitted with circular mats of perforated rubber. The method of securing the mat to the air pipe can be seen from Fig. 45. Over each mat rotates a moulded rubber disc of slightlylarger diameter at a peripheral speed of 2,500 ft. per minute. It is mounted on a driving spindle as shown in Fig. 46. Each spindle is supported and aligned by ball-bearings contained in a single dust- and dirt-proof casting, and each pair is driven from a vertical motor through Tex-ropes and grooved pulleys, a rigid steel structure supporting the whole series of spindles with their driving mechanism. The machine can be supplied, if required, however, with a quarter-twist drive from a lineshaft over flat pulleys.
The air inlet pipes are connected to a main through a valve by which the amount of air admitted to each mat can be accurately controlled. The air is supplied by a low-pressure blower working at about 2 lb. per square inch. It enters the cell through the perforations in the rubber mat and is split up into a stream of minute bubbles, which are distributed evenly throughout the pulp by the action of the revolving disc. By this means a large volume of finely-dispersed air is introduced withoutexcessive agitation. There is sufficient agitation, however, to produce a proper circulation in the cell, but not enough to cause any tendency to surge or to disturb the froth on the surface of the pulp. All swirling movement is checked by the liner-baffles with which the sides of the cell are lined ; their construction can be seen in Fig. 44. They are constructed of white cast iron and are designed to last the life of the machine, the absence of violent agitation making this possible.The pulp must be properly conditioned before entering the machine. It is admitted through a feed box at one end at a point above the first disc, and passes along the length of the cell to the discharge weir without being made to pass over intermediate weirs between the discs. The height of the weir at the discharge end thus controls the level of the pulp in the machine. The froth that forms on the surface overflows the froth lip in a continuous stream without the aid of scrapers, its depth being controlled at any point by means of adjustable lip strips combined with regulation of the air.The Geco New-Cell is made in four sizesviz., 18-, 24-, 36-, and 48-in. machines, the figure representing the length of the side of the squarecell. Particulars of the three smallest sizes are given in Table 27. Figures are not available for the largest size.
Xinhai is a professional R & D and production manufacturer of flotation cells, and has passed ISO9001:2015 international quality management system certification. Xinhai froth flotation separation is sold all around the world.
High-quality equipment manufacturing capabilities, focusing on the research and development and innovation of mineral processing equipment, extending the stable operation time of the equipment, and providing cost-effective services.
A new flotation machine of the reactor-separator type has been designed based on the creation of compatible hydrodynamic conditions for control of the main stages of the flotation process in spatially separated zones of the machine. The dependence of the efficiency of the flotation process on the time of residence of the pulp in the reactor is shown to be of an extreme nature and is determined by the ratio of the rates of formation and destruction of flotation complexes and the rate of coalescence of the bubbles. The manner in which the zones in reactor-separators are organized and connected to one another for the selective flotation of mineral particles should be significantly different than for the treatment of waste water. The application of external vibrations (ultrasound) to mineralized air bubbles in the reactor zone makes it possible to independently regulate the process of particle separation and enhances selectivity in the division of copper sulfides from nickel sulfides.
G. Harbort, E. V. Manlapig, S. K. De Bono, and A. J. Monaghan, Air and fluid dynamics within a Jameson Cell downcomer and its implications for bubble-particle contact in flotation, XXII Int. Mineral Processing Cong. Proc., (2003), pp. 715724.
Yu. S. Karabasov, V. D. Samygin, L. O. Filippov, et al., Russian Federation Patents Nos. 2214871, 2275968, and 2281810, MPK B03D1/24, Pneumatic flotation machine, Publ. 10.27.2003, 05.10.2006, 08.20.2006.
V. D. Samygin, L. O. Filippov, V. V. Panin, and N. Yu. Stenin, Principles of the flotational removal of petroleum products and suspended matter from waste water in a reactor-separator, Proc. V Congr. of Ore-Dressers in the Nations of the CIS, Vol. 1 (2005), pp. 201203.
V. D. Samygin, L. O. Filippov, V. V. Panin, et al, Indices of the flotational removal of petroleum products and suspended matter from waste water with the use of a reactor-separator, ibid., pp. 204205.
V. D. Samygin, N. Yu. Stenin,V. V. Panin, et al., Parameters and regimes for the efficient purification of waste water with the use of a flotation machine of the reactor-separator type, Tsvetn. Met. Chern. Met., Special Publication in Honor of the 75th Anniversary of the Moscow State Institute of Steel and Alloys, October, 2005, pp. 5763.
V. D. Samygin, N. Yu. Stenin, V. V. Panin, and L. N. Krylov, Flotational deep-cleaning of oil-bearing waste water with the use of a reactor-separator, Ekol. Proizvod. Khim. Neftekhim., No. 4(6), 1112 (2006).
V. D. Samygin, L. O. Filippov, N. Yu. Stenin, and a. N. Mostovskoi, Flotation machine of the reactor-separator type for the efficient removal of petroleum products and suspended matter from industrial effluent, Tsvetn. Met., No. 5, 2426 (2007).
Samygin, V.D., Panin, V.V., Filippov, L.O. et al. Development of a reactor-separator flotation machine designed by the Moscow Institute of Steel and Alloys. Metallurgist 54, 394400 (2010). https://doi.org/10.1007/s11015-010-9311-4Get in Touch with Mechanic