mnsteels - premium crusher wear parts

mnsteels - premium crusher wear parts

With more than 30 years of experience in wear casting manufacturing, we are determined to produce the finest manganese liners and are proud to put our name on our products.

Our partners/customers appreciate our communications and order status updates when working with us. Our dedicated customer care team keeps partners/customers' interests in mind, and is always ready to assist.

Mr. Zhou led a team of four to start Great Wall Foundry in Wuzhou, Guangxi, China. With a 200 kg furnace, the foundry started with melting metal scraps into steel blocks and sold them to bigger steel makers as melting material.

Observing the boom in China's economic reform, Great Wall Foundry started to produce manganese jaw liners up to 500 kgs that were popular among quarries in Guangdong province.

In order to increase its manufacturing capacity, Great Wall Foundry moved to a new location at Zhongshan, Guangxi, China. A new foundry was built with four one-ton furnaces, and large jaw liners up to 3 tons were made to meet the demand in the market.

After years of study and research, Great Wall Foundry perfected its techniques of "Clean Melt" and "Die Casting with Sand Layer". These concepts are still the key characteristics of the parts the foundry manufactures. Especially when later new products with a higher manganese content were developed, "Clean Melt" provided a great advantage on the productions of castings with 21% and 25% manganese contents.

With the "Clean Melt" and "Die Casting with Sand Layer" technique, Great Wall Foundry successfully caught the attentions of some industrial leaders in the crusher manufacturing. The foundry started to supply OEM wear parts for partners of leading crusher manufacturers. Its international sales team, MnSteels, was formed and began its first step to the international market.

Guilin Liangjiang International Airport (KWL), us about 200kms from our foundry. Taking the high speed rail from Guangzhou to us (Zhongshanxi Station) is about 2 and half hours, and from Guilin to us (Zhongshanxi Station) is about 1 hour.

Room temperature. All castings go through a cooling phase which takes from 48 hours to 120 hours depending on the thickness of the castings. For example, our C200 plates are about 300 mm thick, so they have to cool down for at least 100 hours. Each casting has a process sheet which lists the related requirements, including cooling time.

Our main products are manganese crusher plates, including cone crusher liners and jaw crusher liners.In addition to other manganese steel parts, we also manufacture high chrome cast iron and other alloys.

We use bottom pour ladle; the temperature is 1,420 degrees centigrade when pouring the first product. Pouring temperature for the rest of the products from the same ladle is lower than 1,420 degrees centigrade.

cme crusher liners - h-e parts

cme crusher liners - h-e parts

H-E Parts liner development program and CME Crusher liners provide customers with application-specific performance at the lowest total operating cost by matching the optimum profile with the most appropriate grade of manganese steel chosen from one of the following ranges:

H-E Parts range of 18% manganese steels that provide a balance between product life and overall cost, and is differentiated from the MnStandard range due to its metallurgical content, manufacturing process and heat treatment.

For most suppliers, selecting the right liner for a specific application is to duplicate the OEM design. If requested, H-E Parts can also supply OEM equivalent designs; however, H-E Parts innovative approach to liner development has consistently demonstrated that the correct liner for a given site is one that has been designed specifically for the application.

By adopting a holistic approach and integrating liner management policies with site specific operating and maintenance practices, crusher liner problems are reduced, freeing up resources for other important jobs and reducing total operating costs.

H-E Parts has built a reputation on the reliability and performance of its CME range of manganese crusher liners, which are designed to be fully compatible with H-E Parts variety of lifting devices, that ensure safety and efficiency are achieved in all service functions. This reputation carries on to H-E Parts flagship MnElite grade of manganese wear products, which typically result in a 35% improvement over lower grades of materials. While this alone is an impressive achievement, it is only a starting point as H-E Parts can normally achieve improvements well beyond a simple extension in liner life whatever the grade of manganese.

H-E Parts International replacement parts are compatible with the makes and/or models of the third-party equipment described. H-E Parts International is not an authorized repair facility of these third parties and it does not have an affiliation with any manufacturers of these third-party products. All brands, original equipment manufacturer (OEM) part numbers or references are owned by the respective OEM entities or their affiliates. These terms are used by H-E Parts International for identification and cross reference purposes only and are not intended to indicate affiliation with, or approval by the OEM, of H-E Parts International or its products.

crushing - astec

crushing - astec

The site navigation utilizes arrow, enter, escape, and space bar key commands. Left and right arrows move across top level links and expand / close menus in sub levels. Up and Down arrows will open main level menus and toggle through sub tier links. Enter and space open menus and escape closes them as well. Tab will move on to the next part of the site rather than go through menu items.

jaw crushers | mclanahan

jaw crushers | mclanahan

Jaw Crushers are used to reduce the sizeof many different types of materials in many applications. The Jaw Crusher was first introduced by Eli Whitney Blake in 1858 as a double-toggle Jaw Crusher. Introduced in 1906, McLanahans Universal Jaw Crusher was one of the first modern era overhead eccentric Jaw Crushers. On the overhead eccentric style Jaw Crusher, the moving swing jaw is suspended on the eccentric shaft with heavy-duty double roll spherical roller bearings.

The swing jaw undergoes two types of motion: one is a swing motion toward the opposite chamber side (called a stationary jaw die due to theaction of a toggle plate), and the second is a vertical movement due to the rotation of the eccentric. These combined motions compress and push the material through the crushing chamber at a predetermined size.

More than 110 years of engineering and customer service experience keep customers running to McLanahan tomeet their production goals. McLanahan Jaw Crushers are proudly made in the USA and have imperial designs. With our grass roots design coupled with listening to customer needs for product enhancement over the years, McLanahan offers traditional hydraulic-shim adjustment Jaw Crushers as well asH-Series Jaw Crushers that featurehydraulic discharge setting adjustment, adjust-on-the-fly chamber clearing in the event the site loses power (once power is restored) and hydraulic relief for overload events with auto-reset.

Whether the traditional hydraulic-shim adjustment or the H-Series Jaw Crushers, both machines have an aggressive nip angle that providesconsistent crushing throughout the entire crushing chamber, which leads to increased production and less downtime on maintenance.

A Jaw Crusher uses compressive force for breaking material. This mechanical pressure is achieved by the crusher'stwo jaws dies, one of which is stationary and the other is movable. These two vertical manganese jaw dies create a V-shaped cavity called the crushing chamber, where the top of the crushing chamber is larger than the bottom. Jaw Crushers are sized by the top opening of the crushing chamber. For example, a 32 x 54 Jaw Crusher measures 32" from jaw die to jaw dieat the top opening or gape opening and54 across the width of the two jaw dies.

The narrower bottom opening of the crushing chamber is used to size the discharge material. A toggle plate and tension rods hold the pitman tight near the bottom of the moving swing jaw. The toggle plate is designed to perform like a fuse and protect the crusher in the event that an uncrushable materialenters the crushing chamber. As a rule, Jaw Crushers have a 6:1 or 8:1 ratio for crushing material. Still using the 32 x 54 Jaw Crusher example, the top size of thefeed entering the crushing chamber has to follow the F80 rule that 80% of the top size feed material is smaller than the gape opening. Using the F80 rule with the 32 x 54 Jaw Crusher, the32 gape opening equals a26 top sized feed, and with the 6:1 ratio of reduction, the discharge setting would be around 4.

Since the crushing of the material is not performed in one stroke of the eccentric shaft, massive weighted flywheels are attached to the eccentric shaft andpowered by a motor. The flywheels transfer the inertia required to crush thematerial until it passes the discharge opening.

While Jaw Crushers are mostly used as the first stage of material reduction in systems that may use several crushers to complete the circuit, the Jaw Crusher has also been used as a second-stage crushing unit. Depending on the application requirements, Jaw Crushers can be used in stationary, wheeled portable and track-mounted locations. The Jaw Crusher is well suited for a variety of applications, including rock quarries, sand and gravel, mining, construction and demolitionrecycling, construction aggregates, road and railway construction, metallurgy, water conservancy and chemical industry.

F100 is the maximum gape opening on a Jaw Crusher. F80 is the feed size to the Jaw Crusher, calculated by taking 80 times the gape opening divided by 100. P80 is the percent passing the closed side setting in tph.

A best practice, if possible, is to blend the material arriving from the source. This will ensure a constant and well-graded feed to the crushing chamber. In turn, this will produce a steady rate of tph andpromote inter-particle crushing that helps break any flat or elongated material. It also aids in equal work hardening the manganese jaw dies and prolonging the life of the jaw dies.

Usually a Jaw Crusher is in an open circuit, but it can be used in a close circuit if the return load is not greater than 20% of the total feed and the raw feed is free of fines smaller than the closed side setting.

Efficiency can be defined by the ratio of the work done by a machine to the energy supplied to it. To apply what this means to your crusher, in your reduction process you are producing exactly the sizes your market is demanding. In the past, quarries produced a range of single-size aggregate products up to 40 mm in size. However, the trend for highly specified aggregate has meant that products have become increasingly finer. Currently, many quarries do not produce significant quantities of aggregate coarser than 20 mm; it is not unusual for material coarser than 10 mm to be stockpiled for further crushing.

cause analysis and problems solving of jaw crusher | hxjq

cause analysis and problems solving of jaw crusher | hxjq

The jaw crusher is mainly composed of a frame, a movable jaw assembly, a movable jaw, a fixed jaw, a triangular wheel, a flywheel, a bracket, a side guard, a discharge port adjusting device and a driving device. Because of its simple structure, easy manufacture, reliable operation and convenient maintenance, it has been widely used in crushing operations in metallurgy, chemical industry and mining industries.

In the jaw crusher, the ore is crushed and reduced to the required particle size. When the moving plate moves away from the fixed plate, the ore is sliding down freely from the upper portion of the crushing chamber to the discharge port under the action of gravity. During this process, the ore slides down along the surface of the jaw plate and causes sliding friction which makes the jaw plate be worn. Therefore, the abrasive wear is an important wear type caused by the squeezed ore.

When the ore is squeezed and ground under the huge mechanical force of the jaw plate, it is easy to form hard sharp edges and corners, and continual interaction between ore and the jaw plate makes the surface of the jaw plate appear very deep scratches, dense grooves and large-area deep pits. As a result, under the strong chiseling action, the jaw plate develops plastic deformation, metal rheology, brittle fracture and spalling, causing the material of jaw plate continuously to migrate and lose, and gradually become thinner. Therefore, chiseling wear is the main form of wear.

Jaw crusher has a large crushing force and fast running speed. Under the action of the huge impact and crushing stress, it withstands long-term and periodic contact fatigue load and is prone to fatigue crack. Therefore, fatigue spalling is also one of the causes of wear.

In order to protect the environment and improve working conditions, a water spray facility is installed on the site of the jaw crusher for dust suppression. At the same time, the water directly contacts the raft which accelerates the oxidation and corrosion of the raft and causes corrosion and wear of the raft.

The wear of the jaw plate presents complexity and diversity and is affected by factors such as materials, abrasives, environmental media, and relative motion. The value of the moving motion is usually reduced to solve the wear problems. In recent years, with the rapid development of computer technology, software simulation is used to comprehensively consider various factors that cause wear, and dynamically imitate of the crushing movement of the jaw plate, so as to more comprehensively analyze the wear rules of the jaw plate and finally reduce its wear rate.

In addition to the wear problem of the jaw plate, there are many other problems caused by parts and components can not be ignored. Next, we will introduce the failure analysis and troubleshooting of the jaw crusher.

4Check the tooth gap size of the tooth plate. If it does not meet the standard, the jaw plate must be replaced, and the relative position of the fixed jaw plate and the movable jaw plate should be adjusted to ensure that the tooth top is fixedly pressed against the tooth root to prevent displacement.

6It is non-bearing temperature rising, but the sealing sleeve of the movable jaw rubs with the end cap, which causes friction heating, or the double embedded cover of the frame bearing seat and the spindle rotate together, causing friction and heat.

6Replace the end cap and the sealing sleeve, or loosen the upper bearing cap of the end of the frame bearing housing which is overheated, press the fuse and the insert cover into the bearing housing groove, and then fix the bearing cover to eliminate the cover rotation.

jaw crusher | primary crusher in mining & aggregate - jxsc mine

jaw crusher | primary crusher in mining & aggregate - jxsc mine

Product Introduction JXSC jaw type rock crusher is usually used as a primary crusher and secondary crusher to reduce the size of medium-hard materials to smaller physical size. Jaw rock crushers are capable of working with the mobile crushing station, underground crushing because of its related small volume. Capacity: 1-1120TPH Max Feeding Size: 120-1200mm Application Mining, metallurgy, building materials, quarrying, gravel & sand making, aggregate processing, recycling, road and railway construction and chemical industry, etc. Suitable Material Granite, marble,basalt, limestone, coal, quartz, pebble, iron ore, copper ore, etc.

40 years of manufacturing and engineering experience keep us innovative and knowledge in the rock break machines and its applications, which thus provide reliable industry rocks crushers and solutions for every customer using jaw crusher manufacturers JXSC machines to meet their production goals. The jaw crusher machine family consists of different sized models that are designed to bring maximum output with minimum cost. Some workplaces have limited conditions and are unable to provide electricity or are underpowered. According to these conditions, JXSC specially designed diesel jaw crusher. The diesel-jaw crusher is actually with electric, but the original jaw crusher was added with a diesel engine equipment that a dual-purpose crusher.

JXSC the crushers machine with a non-welded frame has been proved that it has outstanding solid and durable strength. All the alloy casting frame components turn out that with premium quality, wear-resistant property.

The design of pitman and long stoke improves productivity and reduction. A wider feeding material opening increases the volume of insulating material and makes the ore material entering the crushers crushing chamber smoothly. A sharp angle makes the materials flow down speed faster and reduces the wear cost. Besides, the strike force could be stronger thus increase the production efficiency as well as the reduction ratio.

Types of jaw crushers: on the basis of the stone break equipment size and capacity can divide into a heavy and small(mini) portable jaw rock crushers. According to the working principle can be split into single toggle and double toggle jaw rock crushers machine.

A series of jaw stone crushers use compressive and squeezing force for reducing materials. This physical force is created by the two jaw plates, one of which is a movable plate and another is fixed, both of them are made of manganese. A V-shaped cavity, crushing chamber, is formed and the hydraulic discharge gap width of the crushing chamber, we can determine the suited feeding material size and discharging size, the width of top feeding is larger than that of bottom discharging.

Jaw crusher is a heavy-duty machine that crushes hard materials. So its hence muse be robustly constructed. Crusher frame is made from steel or cast iron. The jaws are made of cast steel. The liners are made fromNi-hard, Ni-Cr alloyed cast iron or manganese steel which can replaceable and use to reduce frame wear. The cheek plates are also made from hard alloy steel and installed to the sides of the crushing chamber to protect the frame from wear.

The jaws can be made in smooth or corrugated, but often corrugated. Because the latter crushing the hard and abrasive ores is better. The angle between the jaws is usually less than 26. This is because a large angle will cause the particle to slip which non-crush.

It uses curved plates to avoid the near the discharge of jaw crusher blocking. The bottom of the swinging jaw is concave, and the relative lower part of the fixed jaw is convex. The materials reduction in size when nears the exit. So the material is distributed over a larger area, and the jaws plates wear less.

The type of crushed materials determines how to design the max amplitude of swing of the jaw and the amplitude adjusted by changing the eccentric. The length from 1 to 7 cm depends on the crusher machine size. Jaw crushers are supplied in sizes up to 1,600 mm (gape)1,900 mm (width). For coarse crushing application (closed set~300 mm), capacities range up to 1200 tph.

Jaw crusher parts must have some wear after a period of use, but the easily damaged parts will wear out more. The price of crushing equipment with the same specifications and handling capacity is different in the material of parts.

Guard Plate The guard plate is made of high-quality high manganese steel, which is located between the fixed plate and the movable plate. The whole body is mainly to protect the jaw crusher frame wall.

Toothed Plate Tooth plate is divided into movable and fixed tooth plate, but both is made from high manganese steel casting. In order to prolong its service life, its shape is designed to be symmetrical. That is when one end of the wear can be used to turn the head. The movable and the fixed teeth plate are the main parts for stone crushing. So the movable teeth plate is installed on the movable jaw to protect the movable jaw.

Toggle Plate The toggle plate is a cast iron piece that has been precisely calculated. It is not only a force transmission component but also the safety parts of the crusher. When the crusher falls into the non-crushing material and makes the machine beyond the normal load, the toggle plate will immediately break. Then the crusher machine stops operation, thus avoiding the damage of the whole machine. The toggle plate and the toggle plate spacer adopt the rolling contact model which less attrition under normal use. It just needs smear a layer of grease on the contact surface is ok.

Triangular Belt When the motor transmits power, the triangle belt is connected with the pulley and the grooved pulley of the motor to drive the eccentric shaft and make the moving jaw move back and forth according to the predetermined track.

The tooth plate of the most jaw crushers are made of manganese steel, bearing linings are made of babbitt alloy, sliding blocks are made of carbon steel, toggle plates are made of cast iron, springs are made of 60SiMn. Regular Inspection and maintenance of the machine can extend its service life. In order to reduce customer costs, we will generally be in the purchase of customers are advised to buy some spare parts. Because once the parts need to be replaced, the temporary purchase will take some time. The wait time may cause the entire breakage line to suspend operations, thereby increasing operating costs.

In short, the jaw stone crushers are mainly used for primary crusher, the crushing stone is relatively large. The types of crusher machine's chamber are deep and no dead zone. It improves that the feeding capacity and output. The crushing ratio is large and the product particle size is even. Shim type outlet adjustment device, reliable and convenient, large hydraulic adjustment range that increased the flexibility of the equipment. Simple structure, reliable work and low operation cost. The adjustment range of hydraulic discharge opening is large, which can meet the requirements of different users, low noise and less dust.

Impact crusher for crushing medium-hard stones, and mostly used for secondary crusher. The impact crushers have a big feeding port, high crushing cavity, high material hardness, big block size and little stone powder. Convenient maintenance, economic and reliable, high comprehensive benefit.

Jiangxi Shicheng stone crusher manufacturer is a new and high-tech factory specialized in R&D and manufacturing crushing lines, beneficial equipment,sand-making machinery and grinding plants. Read More

qiming machinery | wear parts for mining, quarrying & cement industry

qiming machinery | wear parts for mining, quarrying & cement industry

Qiming Machinery is the leading manganese steel, chromium steel, alloy steel, and heat-resisting steel manufacturer in China. We manufacture replacement wear part castings for impact, abrasion, and high heat applications in mining, crushing, grinding, and shredding, for industrial clients worldwide. No matter which wear parts you are interested in, send us the drawings or sample products, you will get the best products and professional suggestions. Know more+

Qiming Machinery manufactures shredder wear parts, crusher wear parts, mill liners, TIC inserts wear parts, apron feeder pans, and other industries wear parts for ore and aggregate crushers, metal and waste shredders, coal-fired power plants, cement industry, and custom application.

Qiming Machinery manufactures AG mill liner, SAG mill liner, ball mill liner, roll mill liner, and other types of mill liners for all popular brands. Material includes Cr-Mo, manganese, chrome, Ni-hard, and other steel.

Our steel casting foundry services include manganese steel casting, chromium steel casting, alloy steel casting, and carbon steel casting. Casting products of our steel casting foundry span across many industries. On the other hand, customized materials also can be manufactured after checked with our professional engineers.

Qiming Machinery manufactures ASTM A128 standard manganese steel wear parts over 12,000 tons per year, which products include cone crusher liners, jaw crusher liners, mill liner, apron feeder pans, hammer mill hammer, and other wear parts.

Qiming Machinery manufactures ASTM A532M standard chromium steel wear parts over 4,000 tons per year, which products include impact crusher blow bars, impact plates, feed tube, VSI wear parts, mill liners, distributor plate, and other wear parts.

As an alloy steel casting foundry, Qiming Machinery specialized in manufacturing low-alloy steel and high-alloy steel parts. Material includes Cr-Mo alloy steel, 30CrNiMo alloy steel, heat-resistant alloy steel. Products include alloy mill liners, alloy hammer, heat-resistant liners

Qiming Machinery has had cooperation with casting foundries to offer carbon steel (ZG250-700, ZG20SiMn, G20Mn5, ASTM A148, ASTM A488, ASTM A781, ASTM A802) wear parts, which include cone crusher shell, jaw crusher flywheel, pitman, adjustment ring, and other parts.

We have a customer from Australia, who runs MVP450 cone crusher to crush hard stone. However, the original wear parts just can work for around 7 days. This customer wants to prolong this mantle and concave span life. After visiting our foundry, this customer wants us to manufacture TIC insert MVP450 mantle and concave to

Qiming Machinery is a professional cone crusher liner manufacture in China. We had exported more than 12,000 tons of cone crusher liners for our customers. Recently, we get a trail order from Serbia to test our Mn18Cr2 HP300 cone crusher mantle and concave. About the feedback, please check the following communication message: T The messages

We have a Philippines customer who has four crushing lines to crush hard stone. There are 1 set HPT300 crushing lines, 1 set PEW760 crushing line, 1 set HP200 crushing line, and 1 set HP300 crushing line. They had tested many foundries crusher wear parts, however, no products have a long working life. From April

Qiming Machinery is the leading manganese steel, chromium steel, alloy steel, and heat-resisting steel manufacturer in China. We manufacture crusher wear parts, shredder wear parts, mill liners, apron feeder pans, and other wear parts for customers.

crushers for sale at grinder crushers screen

crushers for sale at grinder crushers screen

Copyright GRINDERCRUSHERSCREEN.NET 2019 All rights reserved. GrinderCrusherScreen, Screen USA, Hammerhead & Shark design are trademarks or registered trademarks of Screen USA Inc. All other trademarks are owned by the respected brand owners.

Get in Touch with Mechanic
Related Products
Recent Posts
  1. excavator mounted jaw crusher peru

  2. hand aggregate crushers for sale in malaysia

  3. sanme high-strength materials mining jaw crusher fine crusher machine jaw

  4. mupane gold mining pty

  5. sri lanka tangible benefits medium lump coal stone crusher for sale

  6. iron ore mining in laos

  7. second hand zenith crushers

  8. how to use marble edging machine

  9. high quality stone stone crusher in jakarta

  10. different crushing value

  11. vibrating screen manufacturer in italy

  12. idli grinding india

  13. chile high end small basalt wear parts of ball mill manufacturer

  14. crushing plant quarrying

  15. supply crusher warehouse

  16. mobile stone crusher machine in germany

  17. ashworth bros inc conveyor belts metal plastic spiral

  18. ball mills stone crusher project viability

  19. sand production control

  20. raymond millard dell